dpreston1
join:2002-09-26
Fort Lauderdale, FL
| reply to Drogue8
Re: WOL Through Cable Modem and Router?
Thanks for the dl info!!! (Magic Packet)
[text was edited by author 2002-10-04 16:30:02] |
|
kayut
join:2002-12-02
| Hi,
I am from gemany and I can't very good english. Pleas forgive me, if I write something wrong !!
Now my Question:
Do I understand correctly?
It is possible to wake up a PC across the Internet??
IF the Answer is Yes, kann I do it with a "MC 7004 VBR DSL-Router"?
Thanks in advance for your help |
|
fjavier
@ttd.es
| I tried also to do it, and did what is explained in this topic, but it doesn't work for me. I have a 3com 812 router, private network 172.26.0.x with mask 255.255.255.240, so broadcast address is 172.26.0.15
I have put NAT to route UDP port 7 to UDP port 7 of the broadcast address.
It doesn't work. Any idea?
fjescrib@teleline.es |
|
IceTIceT
join:2003-01-02
Fort Worth, TX | SMC 7004 VBR: I cannot create portforwarding on x.x.x.255. What have I to do ?
Thanks ! |
|
kayut
join:2002-12-02 | I have the same problem as EceTIceT.
You can`t use x.x.x.255 (only to 254)by SMC 7004 VBR.
Heeelp |
|
ZeToUnE
@mc.vi
| Me too, I don't speak english fluently !
I have a server (windows 2000 server) and I tried to forward port UDP to the broadcast IP address, but it doesn't work. If I send magic packet from the server, the pc on lan wakes up ! but if I send it over internet, it doesn't work.
I'm using RRAS from windows 2000 server !
The ip address of the public interface is assigned by ISP DHCP server.
The ip address of the private interface is 192.168.0.1
So I tried to forwarding the following port
UDP 7 to 192.168.0.255
but the pc doesn't wake up ! I tested if the server received the magic packet, and it does ! but it seems that the PC doesn't receive the magic packet forwarded
Any idea ? |
|
Nomikal
join:2003-04-23
San Francisco, CA
| I have A DSL/CABLE ROUTER(I use it for DSL) and you must configure your router(As someone stated above). And if you have an onboard NIC you might want to make sure its powered when the system is powered down(On my comp u can't tell by look at the LEDS if its powered or not).
Heres how my configuration looked when i got it to work.
[text was edited by author 2003-04-23 13:25:17] |
|
ZeToUnE
@zenon.com | My routeur is set up as drogue said..
But I can't make it work. |
|
zaimis
join:2003-06-28
Casa Grande, AZ
| I've got a little bit of a weird set up from my ISP. When I trace my public IP from my comp, it looks like this:
1 1 ms 1 ms 1 ms 192.168.0.1 (router's IP)
2 1 ms 1 ms 1 ms 172.19.24.150 (don't know what this is)
3 29 ms 13 ms 13 ms arizona.netbeam.net [216.58.148.244](public IP)
How would I go about setting this up?
Also, on my WAN IP is something weird like 10.1.1.2
Hope I provided enough info to get some help  |
|
