Anonymous Coward
@furball.org | reply to parasonic
Re: X3 gateway owners...
It is, isn't it, unlike that clocky X2. |
|
parasonic
I Am Not A Bot
join:2002-03-29
Atlanta, GA
clubs: | reply to bmn
I got my x3 today. It's cute. |
|
Anonymous Coward
@furball.org | reply to DTVJaimie
What kind of diag tools? A screenshot or three would be nice. |
|
parasonic
I Am Not A Bot
join:2002-03-29
Atlanta, GA
clubs: | reply to DTVJaimie
What is your email address? |
|
DTVJaimie
@us.d | reply to bmn
I have one of the original X3 gateways. I beta tested it for DTV. It has full function DHCP server all 254 IP leased and some other stuff that was restricted with the final release. Has some extra diag tools also. What's it worth to ya? |
|
parasonic
I Am Not A Bot
join:2002-03-29
Atlanta, GA
clubs: | reply to Anonymous Coward
I am NOT going to put a new bus on the device. It will be connected to something that already exists, like 100mbit ethernet. |
|
Anonymous Coward
@furball.org
| reply to parasonic
It is 1.1. The USBF is identical to the X1/X2. The USBH is not working (probably because the drivers isn't in the firmware).
As for 802.11a, good luck. I counted a minimum of 64 lines required just to get the PCI bus working. I don't see 64 on the board. |
|
parasonic
I Am Not A Bot
join:2002-03-29
Atlanta, GA
clubs:
| reply to ElViejoPoeta
Just talked to some guy who's selling me his $20 shipped. Faster processor and faster ethernet could allow for 802.11a adaptivity.
Is the x3 USB 2.0 compatible, or just 1.1? The sucker was designed back in 2000/2001, so I'm guessing 1.1.
--
"We will add your biological and technological distinctiveness to our own. Your culture will adapt to service us. Resistance is futile. We are the Borg." 3.333GHz CRUNCH! CRUNCH! |
|
ElViejoPoeta
join:2001-01-10
Miami, FL
| reply to Anonymous Coward
said by Anonymous Coward:
The HD15 port is labeled "CVD Port" on the board itself.
I have one. If you create a public project to hack on these, you are likely to get a better response. What exactly are you trying to do?
--
See where my mind is: »www.gporcel.net |
|
Anonymous Coward
@furball.org | reply to Anonymous Coward
The HD15 port is labeled "CVD Port" on the board itself. |
|
Anonymous Coward
@furball.org
| reply to bmn
Just got myself a X3. It has a TNETD5320 125mhz MIPS processor with 16MB of SDRAM powering the thing. The U numbers are the mark on the board, the description is my guess(es) on it.
U2 TI TNETD5014 (DSL support)
U7 TI TNETD5100 (DSP)
U6 IDT IDT71V256 (256K SRAM)
U14 TI TNETD5320 (CPU)
U13 Opti FireLink 82C861 (USB controller)
U21&22 Samsung K4S641632E 7.5ns (64mbit SDRAM)
U23 Toshiba TC58V64BFT (64mbit NAND Flash)
U25 (can't read the part number because of label)
U20 Broadcom BCM5221 (802.3u PHY)
There are two JP headers, JP4 and JP5. JP4 is located right next to the CPU, JP5 next to the Flash. Both are 2x7. |
|
TomR_in_MI
Premium
join:2002-12-19
Walled Lake, MI
clubs: | reply to wmcbrine
There is a small picture and some diagrams of the X3 in this thread: »Possible new X3 modem and router conflict... |
|
Anonymous Coward
@furball.org | reply to Turboz
Since this is DMT ADSL, the only way you can interface via WAN is to have a DSLAM handy. You can do a back-to-back using certain SDSL modems (ie, the Netopia 7100s for Rythms/Northpoint), but it required one to supply clock and act as the DSLAM... |
|
Anonymous Coward
@furball.org
| reply to bmn
Is there a public project going on with either X2 or X3 gateways? It would be nice to be able to get a SBC-type X2s that could act as a DSL firewall with mounting / via NFS and such.
Of course, the X2 case is twice as large as it should be... |
|
wmcbrine
Touched by His Noodly Appendage
join:2002-12-30
Laurel, MD | reply to megamanblast
Could someone post a picture of an X3 modem? I've never seen it. |
|
bmn
? ? ?
Premium,ExMod 2003-06
join:2001-03-15
hiatus | reply to megamanblast
you have an IM. |
|
megamanblast
join:2002-08-26
Davis, CA | reply to Turboz
I have x3 modem |
|
Turboz
Computer Nut
join:2002-05-16
Cotopaxi, CO
| reply to bmn
said by bmn  :
I'll try this again... This is a request to all X3 Gateway owners to please contact me regarding your gateway. I'm interesting in getting one or two of these gateways to tweak with the embedded Linux OS present on it. If anyone has one they are willing to part with, please respond below as I am willing to pay shipping for one or two to be sent to me. Thanks,
badmagicnumber
Linux/Unix/BSD geek 
I was wanting to hack around on an X3 myself. I have migrated to SBC and came back to this forum to see if anyone had any info on how to get root on one of these. Does anyone know if they can be interfaced via the WAN port? |
|
nonoy5
-Line Noise Is Hypnotic
join:2002-12-30
Irvine, CA |  reply to bmn
I will check out the model of my brother's modem.
He got his around1 or 2 months before they said they were disconnecting DSL.
- NOnoy |
|
bmn
? ? ?
Premium,ExMod 2003-06
join:2001-03-15
hiatus |  reply to SMCinAZ
Not my doing... |
|
