jakers3
join:2003-08-23
Birmingham, AL
| Please check my stats.
I've had quite a bit of trouble with my line lately. Lots of new construction and hookups in my area. bsdsl techs say I'm getting about all the speed possible on my line.
I'm now getting an average of 925/212 and use to get 1225/221.
I've run Tweak test and set up as recommended and Dr. Ping shows 102.80.
Line test:»/quality/nil/1349833
I'm 17,500 ft. from the co(wire)
How do the line test results look? Any clues about getting back up to my original speeds?
Thanks in advance for any and all help. |
|
Schmengy Brother
@bellsouth.net | Post your line stats (from the wall jack and at the NID) and tweak tests results. |
|
steven506
Premium
join:2003-06-11
Frankfort, KY
| reply to jakers3
I'm 17k feet from the CO on straight copper and my speeds are consistently 1180/210 (give or take a little). I would expect that your speeds would be somewhere around mine.
Post your line stats...I would like to compare them to mine.
Thanks. |
|
ROLLTIDE2
join:2002-10-14
Mobile, AL | What kind of modem do you have ? |
|
jakers3
join:2003-08-23
Birmingham, AL | Westell 2100. |
|
steven506
Premium
join:2003-06-11
Frankfort, KY | reply to jakers3
»AT&T Southeast Forum FAQ »How do I access the Westell line stats and logs? What do the numbers mean?
Please post your results. |
|
jakers3
join:2003-08-23
Birmingham, AL
| reply to jakers3
I should have put this Tweak Test result in the original post.
I have the MTU set at 1491, RWIN at 64620 because those settings give me the best speed results I have found so far.
I'm on Win.XP and the Tweak Test suggested RWIN of 37752 or less give less speed.
»ttester.broadbandreports.com/twe···a=normal |
|
jakers3
join:2003-08-23
Birmingham, AL
| I was typing while Steve's reply was coming through.
Heres the modem result.
DSL Statistics
Line State Up
Modulation G.DMT-Mode
Data Path Interleaved
Transceiver Information
Down Stream Path Up Stream Path
SN Margin (db) 7.5 not defined
Line Attenuation (db) 54.5 not defined
CRC Errors 12931 146
|
|
Shootist
Premium
join:2003-02-10
Decatur, GA | reply to jakers3
Jakers
They need the LINE STATS from the modem. Follow the link above to find out how to do this.
--
Shooter Ready--Stand By BEEP ******** |
|
Schmengy Brother
@bellsouth.net | reply to jakers3
We actually need those stats from the NID too. You have a very low s/n ratio and you need to isolate where the problem is. |
|
jakers3
join:2003-08-23
Birmingham, AL | reply to Shootist
The stats I posted above are the ones needed? |
|
Schmengy Brother
@bellsouth.net | reply to jakers3
Yes those are the stats that are needed but we need you to pull the stats at the regular wall jack and at the NID. You do have a major line problem and your connection is interleaved and it still bearly makes a the cut. |
|
DSLDUDE
Got The Folding Farm Itch
Premium
join:2002-01-07
Norcross, GA
clubs: 
| reply to jakers3
Yes, and if you could try to get them from your NID, that would help also. Your S/N is too low. It may be an inside issue, but we will need the stats from your NID to determine that...
--
Enjoy wood working? Checkthis out! |
|
jakers3
join:2003-08-23
Birmingham, AL | I'm lost now. How do I get the jack and nid stats? |
|
Schmengy Brother
@bellsouth.net
| reply to jakers3
Remember the answer to all of life's questions are in the FAQs! 
»AT&T Southeast Forum FAQ »How to check modem stats, synch rates & speeds from test jack at the NID. |
|
jakers3
join:2003-08-23
Birmingham, AL | I'm going to have to go get some cables to make the nid check. I do have a home run installed with Cat 5 cable running to the jack.
I'll get back in here when I can get wired up for a nid check. |
|
steven506
Premium
join:2003-06-11
Frankfort, KY
| If you have a homerun installed then your line stats from the NID should be nearly identical to the line stats you posted above. It's always good to check anyhow. I know my line stats were virtually identical between the two.
Your line attenuation is a few db's better than mine, but my data path is not interleaved and my sn margin is about double yours.
You definitely have some type of line issue. |
|
jakers3
join:2003-08-23
Birmingham, AL
| OK, I ran a new cat 5 cable from a new jack to the nid and a new cable from the jack to the modem and am still getting the same speeds so it looks like I need to call bsdsl to get them to check the line again. Problem is that they always say the line checks ok.From the replies above it seems that the S/N ratio is the biggest problem.
What is an acceptable S/N ration figure? I'd like to have some reference point to argue from. |
|
Schmengy Brother
@bellsouth.net
| reply to jakers3
Some clarification is needed. Are you saying you connected a new CAT5 to the splitter or did you run the cable directly to the test port on the EBN? If you simply connected it to the splitter than that will not isolate that as a possible porblem. You need to run one single cable from the test port directly to your modem. If you don't have a quality cable that will work you can take the modem outside and connect it to the test port and wait until it syncs. After it does power it down and connect it back to the computer and read the connection log history. |
|
Dan Koerner
join:2000-08-05
Clinton, TN | If it's a Westell, that don't work. My 2200 clears the entire log when it boots.
--
Dan |
|
